Reflectivity of Silver: What It Means for Optical Mirrors | Felix Glass

Reflectivity of Silver: What It Means for Optical Mirrors | Felix Glass

Summary

Silver reflects over 95% of visible light. See how coating thickness, wavelength and oxidation change real mirror performance, and what to specify.

Reflectivity of silver: the number, and what actually changes it

Silver is the most reflective metal across the visible spectrum. Bulk silver reflects roughly 95 to 99 percent of visible light depending on wavelength and surface quality, and it holds that performance further into the infrared than aluminium does. That is why silver is the coating of choice for high-efficiency mirrors, solar concentrators, projection optics and one-way observation glass.

The published figure, however, describes a perfect surface measured in a laboratory. A real coated mirror loses several points to the things that happen between the vacuum chamber and the installation. Here is what those are, and how to specify around them.

1. Where silver's reflectance peaks

Silver's reflectance rises through the blue end of the spectrum, flattens across the visible, then climbs again in the near infrared. In practical terms:

BandTypical silver reflectanceNotes
400–500 nm (blue)Around 90–95%Silver absorbs slightly in the blue; aluminium is competitive here
500–700 nm (green to red)Around 95–99%Silver's strongest region, clearly ahead of aluminium
700 nm – 2 µm (near infrared)Above 98%Excellent for thermal and solar applications

Aluminium, the usual alternative, sits around 88 to 92 percent across the visible. That gap of five to seven percentage points is meaningful in a solar concentrator where every point of reflectance is collected energy, and in a projection system where repeated reflections compound the loss.

2. The four things that pull real reflectivity down

Coating thickness. A silver layer below roughly 80–100 nm is partially transparent rather than fully reflective — which is exactly what a one-way mirror needs, and exactly what a solar mirror must avoid. Thickness is a design parameter, not a quality afterthought.

The adhesion and passivation stack. Silver does not bond well to glass on its own. A thin adhesion layer underneath and a dielectric or metal-oxide overcoat on top are both necessary. The overcoat is what protects the silver from tarnishing; without it, silver reacts with sulphur compounds in the air and darkens within months.

Oxidation and sulphidation. Silver tarnishes. In an industrial atmosphere with sulphur, or in coastal air with chlorides, an unprotected silver coating can lose several percent of reflectance in a year. This is the single most common field failure of silver mirrors, and it is entirely a coating-design problem rather than a silver problem.

Angle of incidence. Metal mirrors hold up reasonably well off-normal, but reflectance at 45 degrees differs from the normal-incidence figure, and for polarisation-sensitive systems the difference is larger. If your design uses the mirror at an angle, specify the reflectance at that angle rather than at normal incidence.

3. Silver versus aluminium versus dielectric

TypeVisible reflectanceStrengthWeakness
Protected silver95–99%Highest broadband visible and NIR reflectanceNeeds a proper passivation stack; more expensive than aluminium
Aluminium88–92%Cheap, robust, good in the UVLower visible reflectance, and the native oxide layer adds loss
Dielectric multilayerAbove 99% in bandExtremely high reflectance with almost no absorptionOnly over a limited wavelength band and angle range

If you need maximum broadband reflectance and can control the environment, protected silver is the answer. If you need the highest possible reflectance at one laser wavelength, a dielectric stack wins. If the part is a cost-sensitive general-purpose reflector, aluminium is still reasonable.

4. Where partial silver is deliberate: one-way mirrors

An interrogation room one-way mirror is a silver coating deliberately kept thin — typically in the range where transmission and reflection are both meaningful — on one face of a glass sheet. The room being observed is brightly lit; the observation room is dark. The observer sees a mirror because the reflected light dominates; the subject sees through because the transmitted light from the dark side is weak relative to what reflects back.

This is why the coating density and the lighting ratio have to be designed together. A "one-way mirror" with too dense a coating cannot be seen through even in a dark room, and one with too light a coating stops behaving as a mirror when the room lights come up. Our standard police observation glass is supplied in 5 mm and 6 mm thicknesses, with the coating density matched to the lighting plan.

5. What to put on the drawing

  • Wavelength band of interest — reflectance is never a single number
  • Angle of incidence the part will actually be used at
  • Whether the environment contains sulphur, salt or solvents
  • Required reflectance at that wavelength and angle, not "high reflectance"
  • For partial mirrors, the target transmission and reflection split

Vague specifications are the main reason a delivered mirror underperforms a sample. If the requirement is written as a number at a wavelength, the coating run can be designed to hit it.

Send your reflectance target for a silver coating quotation

Related reading

Dongguan Felix Glass Co., Ltd. has coated and finished precision optical glass for 19 years. Send the wavelength, the angle and the environment, and we will come back with a coating stack and a reflectance figure rather than a generic data sheet.